HomeMy WebLinkAboutRes2018-046Sponsored by: Hunt
CITY OF SEWARD, ALASKA
RESOLUTION 2018-046
A RESOLUTION OF THE CITY COUNCIL OF THE CITY OF SEWARD,
ALASKA, AUTHORIZING THE CITY MANAGER TO PURCHASE A
NEW 2018 PETERBILT 337 SMALL BUCKET TRUCK IN THE
AMOUNT OF $225,823.00, ADDING A CONTINGENCY ALLOWANCE
OF $22,582.00, AND APPROPRIATING FUNDS.
WHEREAS, The City Council approved Resolution 2017-067, the 2018 electric budget,
which authorized the City Manager to purchase a Small Bucket Truck through the Motor Pool
Fund in the amount of $450,000; and
WHEREAS, the purchase of a new 2018 Peterbilt Small Bucket Truck is consistent with
the City of Seward's policy of the Standardization of Equipment, and in keeping the fleet in good
mechanical, dependable condition; and
WHEREAS, replacement of the 2005 International Small Bucket truck is a necessity to
maintain our fleet of dependable vehicles. The age and weather has deteriorated the truck's
hydraulic system & tank and the electrical wiring system which has rendered the truck
unreliable. In 2014, the electric department spent over 260 man hours replacing the transfer case
and over $20,000 in parts. In the last year, our mechanics replaced all hydraulic hoses and valve
bodies. Since we purchased the 2005 small bucket truck, we have spent over $50,000.00 for
parts, rental equipment, and outside service and countless manhours repairing the truck; and
WHEREAS, the Small Bucket truck is a critical tool for the electrical line crew, used on
a daily basis for outage calls, tree trimming, overhead work, and replacing street lights. The
Small bucket truck hauls trailers, and pulls wire through the underground conduits; and
WHEREAS, Altec Industries has provided the City with a quote for a Small Bucket
truck in the amount of $225,823.00 to include freight.
WHEREAS, the electric department requested quotes from three vendors for pricing and
two vendors were non -responsive.
NOW, THEREFORE, BE IT RESOLVED BY THE CITY COUNCIL OF THE
CITY OF SEWARD, ALASKA that:
Section 1. The City Manager is hereby authorized to purchase a new Peterbilt Bucket
truck from Altec Industries in an amount not to exceed $225,823.00.
Section 2. The purchase order may be increased by an additional amount not to exceed
$22,582.00, reflecting a contingency allowance, at the discretion of the City Manager.
CITY OF SEWARD, ALASKA
RESOLUTION 2018-046
Section 3. The City Council hereby exempts this purchase from competitive
procurements, as allowed by SCC § 6.10.120.5, which exempts competitive procurement for
supplies, materials, equipment or contracted series which can only be furnished by a single
dealer, based on the findings above which are incorporated herein.
Section 3. Funding in an amount of $248,405.00 is hereby appropriated from the Motor
Pool Fund account no. 03000-3000-8103.
Section 4. This resolution shall take effect immediately upon adoption.
PASSED AND APPROVED by the City Council of the City of Seward, Alaska, this
14'h day of May, 2018.
THE CITY OF SEWARD, ALASKA
David Squires, May
AYES: Casagranda, Keil, McClure, Horn, Towsley, Squires
NOES: None
ABSENT: Slater
ABSTAIN: None
ATTEST:
Brenda J. Ballo , MMC
City Clerk
.••q;�
NkOF SEi�y
(City Seal�`.oapo�.,•.0
4
SEAS, � •
~� lF OF F•�-�'S
� 4
�••pJ.Y�JE2e6
1
Agenda Statement
Meeting Date: May 8, 2018
To: City Council
Through: Jim Hunt, City Manager
From: John Foutz, Electric Department Director
Agenda Item: Purchase of a new 2018 Peterbilt Bucket Truck
BACKGROUND & JUSTIFICATION
On November 27, 2017, the Council approved Resolution 2017-067, as part of the 2018 electric
budget, which authorized the City Manager to purchase a bucket truck to replace our small bucket
truck through the Motor Pool Fund in the amount of $450,000.00. After several months of
researching and in conformance with the recommendations of the Motor Pool Vehicle
Replacement Policy that was developed in 2009/2010, we have found a new 2018 Peterbilt bucket
truck that is within our budgeted amount and adequately meets our needs. Standardization of
equipment (purchasing a new Peterbilt bucket truck equipped with Altec equipment) saves money,
improves maintenance efficiencies and helps the electric department respond to customer needs.
The City currently has diagnostic equipment to maintain Peterbilt trucks and Alice equipment
creating efficiencies for similarity and reducing the cost to ratepayers by not needing additional
equipment, tools and software.
Replacement of 2005 International `small' bucket truck, vehicle number 522, is a necessity to
maintain reliable service to the ratepayers of the Seward Utility. Due to age and weathering, the
truck's hydraulic tank & system and the electrical wiring has deteriorated and this has rendered
the truck unreliable. Since 2014, the electric department spent over 260 man hours replacing the
transfer case and over $20,000.00 in parts. Last year, the mechanics replaced all the hydraulic
hoses and valve bodies, which caused the truck to be out of service for over a month during our
construction season. Since we purchased the bucket truck in 2005, we have spent over $113,276.42
for parts, rental equipment, and outside service and countless man-hours repairing it. Finally, the
small bucket truck is a critical tool for the electrical line crew, used on a daily basis for outage
calls, tree trimming, overhead work, and replacing street lights. The small bucket truck hauls
trailers, and pulls wire through the underground conduits.
SCC § 6.10.120.A.5 states, "Specialized products and professional services exempt. To supplies,
materials, equipment or contractual services which can only be furnished by a single dealer, or
which have a uniform published price." Electric Department staff has researched and found Alice
Industries is the only company that will build this mulfifunctioning truck and provide maintenance
on the West Coast. With this new truck and hydraulic system, the Electric Department will be able
to perform work orders more efficiently resulting in lower costs to the customer. Altec Industries
quoted the City a Small Bucket truck in the amount of $225,823.00 including freight. The
administration is also requesting a contingency in the amount of $22,582.00, to account in fuel
costs, since actual shipping costs may be modified to account for fluctuations in fuel charges for
shipping.
Seward Municipal Code References:
6.10.120. Specialized products and professional services exempt.
5. To supplies, materials, equipment or contractual services which can only be furnished
by a single dealer.
6.10.130. Where competitive bid proposals not in public interest.
Restrictions and provisions of this title shall not apply where the city council determines
and makes written findings that the public interest would be best served by not requiring
competitive bids/proposals.
INTENT: To authorize the City Manager to purchase a new bucket truck from Altec Industries in
the amount of $225,823.00. An additional contingency of $22,582.00 may be utilized by the City
Manager, if necessary.
CONSISTENCY CHECKLIST:
Yes
No
N/A
Comprehensive Plan Comprehensive Plan ( 1. 3, 3. 7. 3. 1, 3. 7. 3.2)
Continue to upgrade and expand utilities to meet existing needs and
1.
encourage future development. Expand customer base within the
X
Seward Electric Utility area as a means to reduce energy costs and
improve services.
2
Strategic Plan: The mission of the City of Seward government it is to
provide qualityleadershipand economic wellbeingof its citizens
X
3
Other (list): Consistent with the City's vehicle replacement policy
tXt
established in 2009
FISCAL NOTE: Funding for the purchase of a new Peterbilt Small Bucket truck are available in
the Motor Pool fund account 03000-3000-8103. $450,000.00 has been allocated for use of a
vehicle purchase.
Approved by Finance Department: U t�p
ATTORNEY REVIEW: Yes No
RECOMMENDATION:
Council approve Resolution 2018- , authorizing the City Manager to purchase a new Peterbilt
Small Bucket Truck for an amount not to exceed $248,405.00.
QuoteNurnber: 404113-1
V' Altec, Inc.
S E 11
501 RAILWAY AVE
SEWARD, AK 99664
us
Attn:
Phone:
Email:
Altec Quotation Number*
Account Manager:
Technical Sales Rep:
WILIQ:
CITY OF SEWARD (AK)
PO BOX 167
JFMI& - - - - - - - - -
404113-1
Nick A Zevenbergen
Blake Adams Mendoza
Description ErSie
UDA
Altec Model AT41 M Articulating Telescopic Aerial Device with a fiberglass upper boom
and fiberglass insulator in the articulating arm and proportional joystick upper controls.
Built in accordance to ALTEC's standard specifications and! to include the following
features:
A. Ground to Bottom of Platform Height: 40.8 feet at 7.3 feet from centerline of
rotation (12.45 m at 2.21 m)
& Working Height: 45.8 feet (13,96 m)
C. Maximum reach to edge of platform with Upper Boom Non- overcenter: 30.1 feet
(at 17.3 feet platform height)
D. Upper boom extension: 110 inches
E. Continuous rotation
F, Articulating Arm: Articulation is from -3 to 82 degrees. Insulator provides 19
inches of isolation.
G. Compensation System: By raising the articulating arm only, the telescopic boom
maintains its relative angle in relation to the ground. The work position is
achieved through a single function operation.
H. Upper Boom; Articulation is from -25 to 85 degrees, The fiberglass section
provides a minimum of 10.9 inches of isolation in the upper boom (when retracted
and 42.3 inches when extended).
I. Platform leveling is achieved by a hydraulic master -slave leveling system. This
lifetime system is very low maintenance.
J. The dielectrically tested, insulating upper control system includes the following
boom tip components that can provide an additional layer of secondary electrical
contact protection.
Control Handle: A single handle controller incorporating high electrical resistance
components that is dielectrically tested to 40 kV AC with no more than 400
microampers of leakage. The control handle is green in, color to differentiate it
from other non -tested controllers. The handle also includes an interlock guard
that reduces the potential for inadvertent boom operation.
Auxiliary Control Covers: Non -tested blue silicon covers for auxiliary controls,
Control Console., Neon -tested non-metallic control console plate.
Boom Tip Covers: Non -tested non-metallic boom tip covers. The covers are not
We Wish To Thank You For Giving Us The, Pleasure
And Opportunity of serving You Page 1 of 10
UTILITY EQUIPMENT AND, BODIES SINCE 1929
Altec, Inc.
ft—M P—e-squilatma
dielectrically tested, but they may provide some protection against electrical
hazards.
K Hydraulic system: Open center (full pressure), maximum flow 6 GPM, maximum
operating pressure 3,000.
L. Dielectric rating-, Category C, 46 kV and below
M. Unit is painted with a powder coat paint process which provides a finish -painted,
surface that is highly resistant to chipping, scratching, abrasion and corrosion.
Paint is electrostatically applied to the inside as well as outside of fabricated parts
then high temperature cured prior to assembly ensuring maximum coverage and
protection.
N. Manuals: Two (2) Operator's and two (2) Maintenance/ Parts manuals containing
instructional markings indicating hazards inherent in the operation of an aerial
device.
0. Unit meets or exceeds ANSI 92.2 standards,
MEN=
3. ISO -Boom: Telescopic fiberglass inner boom maintains full dielectric integrity even when
fully retracted
4, Single 1-Man Platform, Fiberglass (insulated), 24" x 30" x 42", Enid Mount, 180 Degree
Rotation
aty ftc-9
11
5. No Platform Elevator 1
6. Platform Mounted Single Handle Controls
7. Material Handling JibANinch, Hydraulically Articulating, Top Mounted, Round (ARM Jib),
8. One (1) Platform Step - located, on the side of the platform nearest the elbow in the
stowed position
9. Toe space on three(3) sides of platform
101. Platform Cover - soft vinyl, 24 x 30 inches (610 x 762 mm)
11. Platform Liner, 24 x 30 x 42 inches (610 x 762 x 1067 mm), 50 kV Rating
12. Hydraulic Tool Circuit at Platform: One set of quick disconnect couplings at the boom tip 1
for open center tools.
11 Hydraulic Tool, Circuit Below Rotation: One set of quick disconnect couplings and 1
control valve for open center tools below rotation.
14. Engine Start/Stop & Secondary Stowage System., 12 VOC powered motor and: pump
assembly for temporary operation of the unit in a situation wherein, the primary hydraulic
source fails. Electric motor is powered by the chassis battery. This feature allows the
operator to completely stow the booms, platform, and outriggers, Secondary Stowage &
StartJStop is activated with an air plunger at the platform or momentary switch at the
lower control station and outriggers.
15, Jib Stick, 36" L, non -extension, non certified, grey in color
16. Slip Ring: Required for engine start1stop, secondary stowage system, and throttle control
options
We Wish To Thank You For Giving Us The Pleasure
And Opportunity of Serving You Page 2 of 10
UTILITY EQUIPMENT AND BODIES SINCE 1929
Altec, Int.
Ite M
+artC
17,
Primary A -Frame Outriggers with 5-degree swivel shoes. For installation on a 41 to 47
inch chassis frame height.
A. Maximum Spread: 135 inches to the outer edge of shoes
B. Ground Penetration: 5 to 11 inches depending on, chassis frame height
C. Outrigger/Unit Selector Valve
D. Outrigger Motion Alarms
E, Outrigger Interlocks. will not allow the unit to be operated until the outriggers
have been at least partially, deployed
18.
Lifting Eye - lifting eye at outer end of lower boom. Rated at 1,000lbs (454kg) lifting
1
capacity
19.
Winch load line swivel hook
1
2&
Altec Aerial Device Powder Painted White
1
21.
Additional Unit Option Static Drain Tubes for Platform.
1
22.
Wilt & Hydraulls; Asx.
Subbase
1
23.
Electric Outrigger Controls for one (1) set of outriggers, drive hydraulic outrigger control
I
valves. Durable weather proof sealed electronic switches mounted in aluminum boxes
located at the rear of the unit unless, otherwise specified.
24,
Other Hydraulic Reservoir 30 Gallon Reservoir
I
-Installed in cargo area.
25.
Temperature Sight Gauge Installed on Reservoir.
1
26.
HVI-22 Hydraulic Oil (Standard).
45
27.
Hydraulic Oil Cooler, Single Fan
1
2&
Hydraulic Oil Heater, Engine Coolant Style
1
29.
Standard Pump For PTO
1
30.
Hot shift PTO for automatic transmission
11
31.
Standard PTO/Transmission Functionality for Automatic Transmissions
1
If chassis is in gear, and PTO switch is activated,. PTO will not engage. Chassis will
remain in gear. Once the chassis is shifted back into gear the PTO will disengage, For
some truck configurations the PTO switch must be turned off to allow the transmission to
shift into gear.
32,
Altec recommends any connection made to the tool circuit be done with Non -Conductive
1
hose. If ordering a Hose reel, Altec recommends ordering a hose reel with
Non -Conductive hose. The lower tool circuit hoses may be, or become, conductive.
Death or serious injury could occur if the unit becomes energized while lower tool circuit
is in use.
33.
Install Tool Circuit with Quick Disconnects, Below Rotation (Male Pressure, Female
I
We Wish To Thank You For GMng Us The Pleasure
And Opportunity of SeMng, You
Page 3 of 10
UTILITY EQUIPMENT AND BODIES SINCE 1929
Altec, I nc.
i4nac,
DgAgrip_tio RAO
Return)
MW
34,
Altec Body
X
Steel Body
X
Body Is To Be Built In Accordance With The Following Altec Standard Specifications:
A. Basic Body Fabricated From A40 Grade 100% Zinc Alloy Coated Steel.
B. All Doors Are Full, Double Paneled, Self -Sealed With Built-in Drainage For
Maximum Weather -Tightness, Stainless Steel Hinge Rods Extend Full Length Of
Door.
C. Integrated Door Header Drip Rail At Top For Maximum Weather Protection.
D, Fender Panels Are Either Roll Formed Or Have Neoprene Fenderettes
Mechanically Fastened.
F. Steel Treated For Improved Primer Bond And Rust Resistance.
F. Automotive Type Non -Porous Door Seals Fastened To The Door Facing.
37.
Smooth Galvanneal Steel Floor
38.
Aerial Service Line With Step (ASLS)
39,
Finish Paint Body Altec White (Applies To Steel And Aluminum)
40.
Undercoat Body
41.
136" Estimated Body Length (Engineering To Determine Final Length)
42.
94" Body Width
43.
46" Body Compartment Height
44,
18" Body Compartment Depth 1
45.
5,5 Inch Drop -in Wood Cargo Retaining Board At Rear Of Body 1
46.
5.5 Inch Drop -In Wood Cargo Retaining Board At Top Of Side Access Step 1
47.
Rope Lights (LED) Around Top And Sides Of Compartment Door Facings 7
48,
Stainless, Steel Rotary Paddle Latches With Keyed Locks 7
491,
All Locks Keyed Alike Including Accessories (Preferred Option) I
50.
Standard Master Body Locking System (Standard Placement Is At Rear, Sidepacks 7
With A Throughshelf/Hotstick Door At Rear, Standard Placement Is At The Front)
51
Gas Shock (Gas Spring) Rigid Door Holders On All Vertical Doors 1
52,
One Chock Holder On Each Side of Body With Retaining Lip In Fender Panel 1
$3.
Hotstick Shelf Extending Full Length Of Body On Curbside 11
We Wish To Thank You For Giving Us The Pleasure
And Opportunity of Serving 'You Page 4 of 10
UITILITY EWPIMENTAND BODIES SINCE 1929
Altec, Inc.
0"Ridation
Edo
54,
Standard Drop -Down Hotstick Door For One (1) Shelf On Curbside, Stainless Steel
I
Slam Paddle Latch With Keyed Lock
55.
1st Verticat (SS) - Adjustable Shelf With Removable Dividers On 2" Centers
2
56.
2nd Vertical (SS) - Adjustable Shelf With Removable Dividers On 2" Centers
2
57.
1 st Horizontal (SS) - Adjustable Shelf With: Removable Dividers On 2" Centers
1
58.
Rear Vertical (SS) - Locking Swivel Hooks On An Adjustable Rail - Left Wall
1
59.
Rear Vertical (SS) - Locking Swivel Hooks On An Adjustable Rail - Rear Wall
4
60.
Rear Vertical (SS) - Locking Swivel Hooks On An Adjustable Rail - Right Wall
1
61.
1st Vertical (CS) - Adjustable Shelf With Removable Dividers On 2"' Centers
2
62.
2nd Vertical (CS) - Gripstrut (Preferred) Access Steps w/ Two (2) Sloped Grab Handles,
1
Vented Battery Storage (Keyed Lock)
63.
1st Horizontal (CS) - Adjustable Shelf With Removable Dividers On 2" Centers
1
64.
Rear Vertical (CS) - Locking Swivel Hooks On An Adjustable Rail - Left Wall
1
65.
Rear Vertical (CS) - Locking Swivel Hooks On An Adjustable Rail - Rear Wall'
4
66,
Rear Vertical (CS) - Locking Swivel Hooks On An Adjustable Rail - Right Wail
1
67,
36" L Steel Tailshelf, Width To Match Body
1
6&
Steel' Cross Storage Located Between Tailshelf Floor And Top Of Chassis Frame Rail,
1
With Drop Down Doors And Keyed Latches On Streetside And Curbside, As Wide As
Possible
69.
Smooth Galvanneal Steel Tailshelf
1
70C .
Steel Top Opening Storage Box, One (1) Treadplate Lid, Gas Props, Hasp Lock, Handle
2
Parallel To Ground And Centered (2 Handles for Boxes Greater Than 108") One (1)
Installed Streetside compartment tops with unistrut.
-20OO IN H
-Full length and width of compartment tops.
One (1) Installed Curbside rear compartment tops with unistrut, behind access step.
-20,00 IN H
-Full length and width of horizontal and rear vertical compartment tops,
13gdy ang Phassis Armigri2a
71. ICC (Underride Protection) Bumper Installed At Rear 1
72. T-125 Style Pintle Hitch (30,000 LB MIGTW with 6,000 LB MVL) 1
73. Set Of D-Rings for Trailer Safety Chain, installed one each side of towing device mount. 1
74. Rigid Step Mounted Beneath Side Access Steps (Installed To Extend Approx. 2"
Outward)
We Wish To Thank You For Giving Us The Pleasure
And Opportunity of serving You Page 5 of 20
UTILITY EQUIPMENT AND BODIES SINCE 1929
Altec, Inc,
Itemagagripim
P-rdiss
75.
Platform Access Step From Body Floor
76.
Platform Rest, Rigid with Rubber Tube
77.
Boom Rest for a Telescopic Unit
78.
Plastic Outrigger Pad, 18" x 18" x 1 ", Black With Handle
2
79,
Outrigger IPad Holder, 20:" L x 20" W x 3" H, Fits 19.5" x 19.5" x 2"' And Smaller Pads,
2
Bolt -On, Bottom Washout Holes, 3/4" Lip Retainer
80,
Pendulum Retainers For Outrigger Pad Holders
2
81.
Mud Flaps With Altec Logo (Pair)
1
82.
Wheel Chocks, Rubber, 9.75" L x 7.75" W x 5.00" H, with 4" L Metal Hairpin Style
1
Handle (Pair)
83.
Slope Indicator Assembly For Machine With Outriggers
1
$4.
Fold Over, Post Style Cone Holder (Holds up to four 15"x15" large cones) Mounted on
1
Street side rear Tailshelf.
$5.
Safety Harness & 4.5 FT Lanyard (Medium To X-large)
1
86.
10 LB Fire Extinguisher With Heavy Duty Bracket, Installed
1
87.
Driveaway Safety Kit
1:
88.
Vinyl manual pouch for storage of all operator and parts manuals
1
ri
89,
Compartment Lights Wired To Dash Mounted Master Switch 1
90.
Lights and reflectors in accordance with FMVSS #108 lighting package, (LED With 1
Incandescent Reverse Lights)
91.
Altec Standard Amber LED Strobe Light with Brush Guard Post mounted on front of 2
body.
-One (1) each side.
912,
4-Corner Strobes, Amber, LED, Two (2) Surface Mounted Lights In Grille, Two (2) 1
Round Lights At Rear
93.
Cargo Light, LED, 4"' DIA, Grommet Mounted Installed on the interior cargo walls. 4
-Two (2) on each side.
-Approx 12.00 IN H from the cargo floor.
94.
Go -Light Brush Guard (Not for Stryker Models) 2
95.
Remote Spot Light, LED, Permanent Mount with Programmable Wireless Remote 2
Installed on Post, front of body.
-One (1) each side.
-Inboard, of Strobes.
We Wish To Tharik You For Gluing Us The Pleasure
And opportunity of Serving You Page 6 of 10
UTILITY EQUIPMENT AND BODIES SINCE 1929
Altec, Inc.
g r j ai ri —on
_QAY
96.
Dual Tone Back -Up With Outrigger Motion Alarm
1
97.
Altec Standard Muilti-Point Grounding System
3
98.
7-Way Trailer Receptacle (Blade Type) Installed At Rear
1
99.
Electric Trailer Brake Controller (Tekonsha Voyager #9030)
1
100.
Aftec Modular Panel System (AMPS) - Includes Mounting Panel and Accessory
1
Switches
101.
Power Distribution Module Is A Compact Self -Contained Electronic System That
11
Provides A Standardized interface With The Chassis Electrical System. (Includes
Operator's Manual)
102.
Install secondary stowage system.
1
1!03.
Install Remote Start/Stop system in Final Assembly,
1
104.
Install Outrigger Interlock System
1
105.
Standard Duty Secondary Stowage Pump
1
106.
PTO Indicator Light Installed In Cab
1
Ort
107,
Powder Coat Unit Altec White
108.
Finish Paint Body Accessories Above Body Floor Altec White
109,
Altec Standard; Components mounted below frame rail shall be coated black by Altec.
i.e. step bumpers, steps, frame extension, p:intle hook mount, dock bumper mounts,
D-rings, receiver tubes, accessory mounts, light brackets, under -ride protection,
etc.Components mounted to under side of body shall be coated black by Altec. i.e.
Wheel chock holders, mud flap brackets, pad carriers, boxes, lighting brackets, steps,
,and ladders.
110.
Apply Non -Skid Coating to all walking surfaces
111.
English Safety And Instructional Decals
1:112.
Vehicle Height Placard - Installed In Cab
113,
Placard, HVI-22 Hydraulic Oil
114,
Dielectric test unit according to ANSI requirements,
115.
Stability test unit according to ANSI requirements,
116.
Non -Focus Factory Build
117.
Delivery Of Completed Unit
118.
Inbound Freight
We Wish To Thank You For Giving Us The Pleasure
And Opportunity of Serving You Page 7 of 20
UTILITY EQUIPMENT AND BODIES SINCE 1929
Altec, lnc.
(tern
grn tnacn
lrice
119,
Installation - AT41'M
120.
.81
Chassis
1
121.
Altec Supplied Chassis
1
122.
2016 Model Year
1
123.
Peterbilt 337
1
1241.
4x4
1
125.
911 Clear CA (Round To Next Whole Number)
1
126.
Regular Cab
1
12.
Chassis Gab
1
128.
Chassis Color - White
1
129.
Chassis Wheelbase Length - 162 inch
1
130.
Paccar PSG-8
1
131,
330, HP Engine Rating
1'
132.
Allison 3000 RIBS Automatic Transmission (Left and Right Side PTO Openings Only)
1
133,
CVWR 33,015 LBS
1
134.
12,000 LBS Front GAWK
1
135.
21,000 LBS Rear CAWR
1
136.
Other Front Tire Size Off Road, Sipped Tires
1
137,
Other Rear Tire Size Off Road, Sipped Tires
1
138,
Hydraulic Brakes
1
139.
Park. Brake In Rear Wheels
1
140.
3365270 - Peterbilt Vertical Exhaust (Right -Horizontal -Under Cab -Vertical)
1
141.
No Prewire Chassis
1
1.4Z
No Idle Engine Shut -Down Required
1
143.
0-State Emissions
1
144.
Clean Idle Certification
1
145.
Peterbill 50 Callon Fuel Tank (Under Cab Lett' Hand)
1
We Wish To Thank You For Giving Us The Pleasure
And Opportunity of Serving You
Page 8 of 10
UTILITY EQUIPMENT AND SODI S SiNCE 1929
Altec, Inc.
D"sription
QW Edo
146.
Peterbilt 11 Gallon DEF Tank (Under Cab Left Hand)
147.
Chassis Without Front Frame Extensions
145.
120,000 Yield Strength (PSI)
149.
Temporary Mount Batteries (Requires Relocation By Altec)
150.
Air Horn Under Cab
151.
AM/FM Radio
151
Cruise Control
151
Keyless Entry
1154.
Power Door Locks
1155.
Power Windows
156.
Tilt Steering Wheel
157.
Block Heater
168.
Air Ride Drivers Seat
1159.
Air Ride Passenger Seat
1 6,0.
Additional Chassis Option Powered & Heated Mirros.
161.
Addilignal FdQft
Standard Altec Warranty. One (1) year parts warranty, one (1) year labor warranty,
ninety (0) days warranty for travel charges, limited lifetime structural warranty
162.
Documentation Fees
163.
Ocean Freight
Alter Industries, Inc.
BY
Unit / Body I Chassis Total 225,823.00
FET Total 0.00
Total 225,82100
We Wish To Thank You For Giving; Us The Pleasure
And Opportunity of Serving You Page 9 of 10
UTILITY EQUIPMENT AND BODIES SINCE 1929
Alec, Inc.
I U li ffiNVID4014
Notes:
RECOMMENDED OPTIONS AND ACCESSORIE& These options are not included in the quote total price.
Selected opfions wfil change the quote total. Any options added after initial order will be re -quoted,
Altec Backup Camera System, 7" Color LCD Monitor, Heated Infrared Camera With Day/Night Sensor And
Audio
ADD $942.00
EZ Trac Hydraulic Front Axle, in lieu of Mechanical 4x4 drivetrain
ADD $10,612,00
We Wish To Thank You For Giving Us The Pleasure
And Opportunfty of Serving You
Page 10 of 10
UTILITY EQUIPMENT AND BODIES SINCE 1929